1.Before use, please shave off the hair in the hair removal area, clean the hair removal area and wipe it clean. Ensure that the hair follicles under the skin are able to absorb the maximum amount of energy to achieve optimal hair removal.
2. Connect the power adapter, turn on the power, and wear the special protective eyewear provided with the product. The background light of the hair removal meter display is lit and the status is "OFF".
3. Long press the "On/Off/Stand Size" button for 2 seconds, the hair removal machine will start. Check the current working status by referring to the previous "Display Introduction".
4. Press the function switch button and enter the hair removal mode when the screen is displayed as HR.
5. The machine is equipped with 1 to 9 gears, short press the "switch/stall size" button to adjust the light wave intensity. For the first time, please start from 1st gear and strengthen the gear according to your own experience.The higher the gear is, the better the effect will be.
6.Light setting.
Manual light setting (for hair removal of small area).
The defaults are manual, i.e., the light is emitted once by one pressing of the flash button. Slide out light setting (for hair removal of large area).
After the hair removal machine is turned on, press and hold the flash button, the hair removal machine will switch to slide-out light mode. All you need to do is hold the head of the lamp vertically against the skin and the hair removal device will automatically shine its light.
7.Attach the lamp head to the part where hair removal is required and use it vertically.
(1)When the hair removal device is in manual light mode, wait for the "LCD screen" to flash, press the "lash emit button" to emit a flash, the light head covers the area to complete the hair removal. Move the head of the lamp to the next hair removal area and hold it close to the skin, wait for the "LCD screen" to flash and press the "Flash Emit button" to emit a flash. In successive cycles, 2-3 exposures are recommended for each part.
(2)When the hair remover is in sliding light mode, a long press on the "Flash Emit button" emits a flash of light, meaning that the area covered by the lamp head is complete. Move the head of the lamp to the next hair removal area and hold it close to the skin, the hair removal device emits a flash of light.In successive cycles, 2-3 exposures per part are recommended.
Tip: When in slide out mode, the head is fully pressed against the skin, and can flash continuously for 8 seconds while the head is sliding.
8.After the operation is completed, long press "switch on/off" for 2 seconds to turn off the machine; When the hair removal machine is on, it will automatically turn off if there is no action for 5 minutes.
9.Pull the adapter plug, then remove the adapter from the power outlet.
10.After ten minutes, allow the surface of the lamp to cool and wipe the lamp with a non-alcoholic wet wipe or soft paper towel.
11.After cleaning, put the hair removal machine and adapter back into the box and place the hair removal machine in a ventilated dry place out of reach of children.
12. Care for the skin in the light-receiving areas. 20 minutes after the end of hair removal, you can choose moisturizing skin care products to the hair removal area for hydration and repair. If there is discomfort, apply cold compresses for 30-60 minutes until the skin is free of burning pain.
Attention
①Apply aloe vera gel or similar moisturizing cream to the hair removal area after hair removal, do not use harsh cosmetics immediately.
②Ensure that the treatment area is clean before shedding.lt is recommended to wash the skin with cold boiling water, and not to touch water for 2 hours after operation. Sunbathing, warm water baths, steam baths, etc. are not recommended within 48 hours.
③Avoid exposing the hair removal area to strong sunlight for 2 hours after hair removal, and apply sunscreen before outdoor activities.
④Do not swim in a sanitized pool for 48 hours after waxing.
⑤Do not press the trigger button continuously, just press once, each part is recommended to irradiate 2-3 times. (The entire head of the lamp fits tightly against the skin area in one place).
⑥The machine should not work for more than 25 minutes continuously, if the hair removal area is large, it can be divided into several times (after 10 minutes, turn off the machine and unplug the power, after 10 minutes' rest, you can continue to use it).
Service cycle
Hair has a certain growth cycle, and short-term use does not complete permanent hair removal. The entire treatment course requires 2-6 months. Only long-term adherence to this product will have an effect.
First month (use once every 3-5 days)
After iradiation, the hair flliles begin to atrophy, and the hair gradually becomes soft and thin.
Second month (use once a week)
Continuously irradiated hair has slowed down growth, with significant hair loss.
Third month (use once every 15 days)
After the hair follicles are irradiated according to the cycle, the hair roots fall off without leaving black spots and the skin is smooth.
Fourth month (use once every 30 days)
96% of the hair stops growing, achieving permanent hair removal and perfect skin.
- Introduction of product button functio.png (70.45 KiB) Viewed 13698 times
